How to Make Earrings: Dangle, Stud and Hoop Earrings Step by Step

The easiest earrings to make are dangle earrings: attach a charm to an ear wire with a jump ring. For stud earrings, glue a flat charm or cabochon onto an earring post with a flat pad and add a back. You need two pairs of pliers, jump rings, ear wires or posts, and charms.
What you need
- Two pairs of chain-nose pliers (or one chain-nose and one round-nose)
- Earring charms or any charms with a loop
- Jump rings, 4–6 mm is a good all-round size
- Ear wires / hooks for dangles, or earring posts and backs for studs
- For studs: two-part epoxy or jewelry glue




Method 1: Simple dangle earrings
- Open a jump ring by twisting the ends front-to-back with two pliers.
- Slide on the charm. Check which side should face forward.
- Hook the jump ring through the loop of the ear wire and twist it closed until the ends meet flush.
- Make the second earring as a mirror image so both charms face outward.
Method 2: Glue-on stud earrings
- Choose flat-backed pieces: small charms without loops, cabochons, or stamped blanks.
- Pick posts with a flat pad smaller than the back of your piece so the pad does not show.
- Lightly sand the pad and the back of the charm for better grip, then wipe them clean.
- Apply a small dot of two-part epoxy, press the post in place and let it cure fully (usually 24 hours) before wearing.
- Add butterfly or rubber backs. Not sure which? See Types of Earring Backs.
Many of our earring studs come ready-made with the post attached, so you can skip the gluing step entirely.
Method 3: Hoop earrings with charms
- Start with hoop earrings or endless hoops.
- Slide a charm directly onto the hoop if its loop is large enough, or attach it with a small jump ring.
- Close the hoop and check that the charm swings freely.
Method 4: Multi-tier connector earrings
Connectors have a loop on each end, so you can stack elements: ear wire → connector → jump ring → charm. Try a geometric connector over a moon or leaf charm for a long statement earring, and keep all the metal in the same finish.
Can I make my own ear wires?
Yes. Cut about 5 cm of 20–21 gauge wire, make a small loop at one end with round-nose pliers, bend the wire over a pen or mandrel, and file the end smooth. Instructions and the different hook styles are in Types of Earring Hooks.
Earrings for sensitive ears
The part that goes through the piercing matters most. Use ear wires or posts in 925 sterling silver or stainless steel, and use brass, copper or plated charms below them.
Design ideas
- Celestial: moon and star charms on raw brass ear wires
- Botanical: leaf and flower charms in mixed finishes
- Minimal: a single geometric connector on a stud post
- Personal: tiny letter charms as mismatched initials
Frequently asked questions
What gauge wire is best for earrings?
20 or 21 gauge (about 0.7–0.8 mm) fits standard piercings comfortably.
What glue should I use for stud earrings?
A two-part epoxy gives the strongest, longest-lasting bond for metal to metal. Let it cure fully before wearing.
How do I make earrings hang straight?
Make sure the jump ring is fully closed and, if needed, add a second jump ring so the charm faces forward.
Shop Earring Charms
View all →More jewelry making guides
All guides →
How to Stamp Metal Jewelry: A Beginner's Guide to Stamping Blanks
Metal stamping needs steel letter stamps, a 1–2 lb hammer, a steel bench block and soft-metal blanks like brass or copper. Strike...
Jump Ring Sizes Chart: Gauge, mm and How to Open and Use Jump Rings
Jump rings are sized by outer diameter in mm and wire thickness in gauge or mm. 4–6 mm rings in 0.7–0.8 mm...
Types of Earring Hooks and Ear Wires (and How to Make Your Own)
Fish hooks (French wires) are the most common earring hooks; leverbacks and kidney wires are the most secure; hoops, threaders and shepherd...
